Sti 1221A Manual do Utilizador descarregar pdf

Safety Technology International, Inc.

2306 Airport Road • Waterford, Michigan 48327-1209

Phone: 248-673-9898 • Fax: 248-673-1246

Toll Free: 800-888-4784 • E-mail: [email protected]

Web: www.sti-usa.com

Safety Technology International (Europe) Ltd.

Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch

Worcestershire • B98 0HU • England • Tel: 44 (0) 1527 520 999

Fax: 44 (0) 1527 501 999 • Freephone: 0800 085 1678 (UK only)

E-mail: [email protected]om • Web: www.sti-europe.com

INSTALLATION OF STI-1221A STROBE DAMAGE STOPPER

All speciﬁcations and information shown were current as of publication and are subject to change without notice.

INSTALLATION NOTES

1. Damage Stopper must be installed to comply

with applicable NEC, NFPA and local codes.

2. In areas where frequent wash downs occur,

standoff blocks must be used.

3. Damage Stopper may be installed outdoors

when appliance carries an outdoor rating.

Electronic warranty form at www.sti-usa.com/wc14

1221AIS APRIL2006

CLEANING INSTRUCTIONS

Rinse with water to remove abrasive dust and dirt. Wash with soap or mild detergent, using a soft cloth

(do not scrub). Rinse once more then dry with a soft cloth or chamois. To remove grease or wet paint,

rub gently with a cloth wetted with naphtha. Then wash and rinse. DO NOT USE RAZOR BLADES.

INSTALLATION INSTRUCTIONS - REFER TO EXPLODED VIEW

1. Insert the (4) 06297T external mounting tabs into the frame assembly slots.

2. Using back box assembly as a template, place against mounting surface at proper location according

to NFPA 72.

3. Mark and drill (4) holes 1/4 in. (6.3mm) diameter, 1 1/4 in. (32mm) deep.

4. Insert the (4) anchors into the wall.

5. Mount back box to wall with screws.

6. Install electrical ﬁttings as needed.

7. Install strobe appliance.

8. Install cover with clips and screws.

9. Test appliance according to appliance manufacturer’s instructions.

FOR CONDUIT INSTALLATION (NOT INCLUDED)

“A” Rain-tight hub with neoprene o-ring threaded for 3/4 in. NPT

rigid conduit

“B” 3/4 in. female adapter

“C” 3/4 in. - 1/2 in. reducing bushing

“D” Galvanized 1/2 x 1 in. conduit nipple

“E” 1/2 in. conduit lock nut

“F” 4 in. square back box

“G” 4 in. square box extension (optional). Use to extend strobe into

cover area.

HORIZONTAL CENTERLINE

OF ENCLOSURE

CENTERLINE

MOUNTING BOSS

FOR BACKBOX

MOUNTING

HEIGHT 80 in.

FRONT VIEW OF ENCLOSURE

#8-32 x 3/8 in.

MACHINE SCREWS

(NOT INCLUDED)

DRILL FOR CONDUIT ENTRY

HEIGHT

7.75 in.(197mm)

WIDTH

5.25 in.(133mm)

DEPTH

6.5 in.(165mm)

629761 NEOPRENE GASKET

19013 SCREW

#10 x 1 1/2 in.

(4) PROVIDED

19033 ANCHOR

(4) PROVIDED

06297T MOUNTING

TABS (4) PROVIDED

06297A BACKBOX

NEOPRENE GASKET

3 3/8 in.

(86mm)

3/4 in.(44mm)

629763 STANDOFF BLOCKS

(4) PROVIDED

19047 #8-32 x 3/8 in. SOCKET

HEAD CAP SCREWS

(4) PROVIDED

01221 COVER ONLY

629764 RETAINING CLIP

(4) PROVIDED

629762 DRAIN SCREEN

INCLUDED BUT NOT

FACTORY INSTALLED

01221 COUVERCLE SEULEMENT

HORIZONTAL CENTERLINE

OF ENCLOSURE

CENTERLINE

MOUNTING BOSS

FOR BACKBOX

MOUNTING

HEIGHT 80 in.

FRONT VIEW OF ENCLOSURE

#8-32 x 3/8 in.

MACHINE SCREWS

(NOT INCLUDED)

DRILL FOR CONDUIT ENTRY

HEIGHT

7.75 in.(197mm)

WIDTH

5.25 in.(133mm)

DEPTH

6.5 in.(165mm)

629761 NEOPRENE GASKET

19013 SCREW

#10 x 1 1/2 in.

(4) PROVIDED

19033 ANCHOR

(4) PROVIDED

06297T MOUNTING

TABS (4) PROVIDED

06297A BACKBOX

NEOPRENE GASKET

3 3/8 in.

(86mm)

3/4 in.(44mm)

629763 STANDOFF BLOCKS

(4) PROVIDED

19047 #8-32 x 3/8 in. SOCKET

HEAD CAP SCREWS

(4) PROVIDED

01221 COVER ONLY

629764 RETAINING CLIP

(4) PROVIDED

629762 DRAIN SCREEN

INCLUDED BUT NOT

FACTORY INSTALLED

01221 COUVERCLE SEULEMENT

HORIZONTAL CENTERLINE

OF ENCLOSURE

CENTERLINE

MOUNTING BOSS

FOR BACKBOX

MOUNTING

HEIGHT 80 in.

FRONT VIEW OF ENCLOSURE

#8-32 x 3/8 in.

MACHINE SCREWS

(NOT INCLUDED)

DRILL FOR CONDUIT ENTRY

HEIGHT

7.75 in.(197mm)

WIDTH

5.25 in.(133mm)

DEPTH

6.5 in.(165mm)

629761 NEOPRENE GASKET

19013 SCREW

#10 x 1 1/2 in.

(4) PROVIDED

19033 ANCHOR

(4) PROVIDED

06297T MOUNTING

TABS (4) PROVIDED

06297A BACKBOX

NEOPRENE GASKET

3 3/8 in.

(86mm)

3/4 in.(44mm)

629763 STANDOFF BLOCKS

(4) PROVIDED

19047 #8-32 x 3/8 in. SOCKET

HEAD CAP SCREWS

(4) PROVIDED

01221 COVER ONLY

629764 RETAINING CLIP

(4) PROVIDED

629762 DRAIN SCREEN

INCLUDED BUT NOT

FACTORY INSTALLED

01221 COUVERCLE SEULEMENT

INSTALL CLAMP IN NOTCH 2 AS SHOWN

INTERNAL DIMENSIONS

REMARQUES SUR L’INSTALLATION

1. Le Stopper de dégâts doit être installé de sorte

à être conforme avec les normes NEC, NFPA

applicables et les codes locaux.

2. Dans les zones où des jets d’eau fréquents

surviennent, des blocs de détection à distance

doivent être utilisés.

3. Il est possible d’installer un Stopper de dégâts à

l’extérieur lorsque l’appareil est homologué pour

utilisation à l’extérieur.

1 2

Resumo do Conteúdo

Página 1 - REMARQUES SUR L’INSTALLATION

Safety Technology International, Inc.2306 Airport Road • Waterford, Michigan 48327-1209Phone: 248-673-9898 • Fax: 248-673-1246Toll Free: 800-888-4784

Página 2 - STI-1210 / STI-1221 SERIES

• This enclosure is rated to protect signaling appliances indoors and in areas of indirect weather exposure.The cover may be used outdoors only with d

Comentários a estes Manuais

Sem comentários

Sti 1221A Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Segurança Sti 1221A. STI 1221A Manuel d'utilisation Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Segurança Sti 1221A